
How to Install Exclusion Fencing Correctly
A single low spot, loose apron or poorly hung gate can undo an otherwise solid boundary. To install exclusion fencing correctly, the fence needs to be designed around the animal you are keeping out, the ground it will cross and the pressure it will face over time. It is not simply a matter of putting up higher mesh.
For rural properties, exclusion fencing is often used to reduce damage from kangaroos, wallabies, deer, foxes, rabbits, wild dogs or other pest animals. The right approach varies considerably. A fence that helps manage rabbits along a vegetable patch has very different requirements from one protecting young vines, pasture, livestock feed or a larger acreage boundary from deer.
Start with the animal and the purpose
The most common fencing mistake is choosing a height, mesh size or footing detail before being clear about the problem. Watch for tracks, droppings, rub marks, digging and the direction animals are travelling. Speak with neighbours where practical. Wildlife and pest animals often follow creeks, shelter belts, ridgelines and established gaps in old fencing, so the pressure may be concentrated rather than evenly spread.
Deer and kangaroos generally call for a taller, well-braced fence with no easy jumping points. Rabbits require close mesh at ground level and a properly managed barrier below or along the ground to stop digging underneath. Fox exclusion may need small apertures near the bottom and careful attention to gates, drains and corners. If the fence is intended to protect stock as well as exclude pests, that also affects the mesh, wire configuration and gate layout.
There is no useful one-size-fits-all specification. The best fence balances the target species, the value of what is being protected, local terrain, maintenance access and budget. Spending money on height while leaving a gap under a gate is rarely money well spent.
Plan the line before materials arrive
Walk the full fence line before setting out. This is the time to identify gullies, rocky ground, wet areas, erosion paths, old stumps, creek crossings and places where machinery needs to pass. On Yarra Valley acreage, a line that looks straightforward from the driveway can become steep, boggy or heavily treed once work begins.
Choose the most practical alignment, not always the shortest one. A slight diversion around a wet hollow, a large tree or a difficult rock shelf can make construction stronger and future repairs far easier. At the same time, avoid creating a route that animals can use to funnel around the end of the fence.
Mark corners, strainers, gateways and changes in direction. Allow enough room to bring in materials and operate equipment safely. If you will need to slash, inspect or repair the fence later, make sure there is an accessible side of the line. A well-built exclusion fence still needs regular checking, particularly after storms, windfall branches or periods of high animal activity.
Check approvals and shared boundaries
Before starting, confirm property boundaries and discuss works on shared fence lines with adjoining owners. Depending on the location and type of work, approvals or specific requirements may apply near roads, waterways, bushland or protected vegetation. It is far easier to sort this out at the planning stage than move a completed fence later.
Build a foundation that will hold tension
Exclusion fencing puts consistent load on end assemblies, corners and turns. These are not places to cut corners. Strong strainers, properly installed stays and suitable bracing give the fence something solid to pull against when mesh and line wires are tensioned.
Post size, spacing and depth depend on soil conditions, fence height, wire load and the length of each run. In firm ground, a post may drive well and hold strongly. In sandy, wet or fractured ground, the same approach may not provide enough purchase. Steep slopes also create uneven loads and may need closer post spacing or additional support.
Set end and corner assemblies first, then run a line to keep intermediate posts straight. A fence that wanders may still stand, but it is harder to tension evenly and more likely to develop weak spots. Keep the fence line clear enough that mesh can sit against the posts without being pushed out by rocks, roots or heavy vegetation.
Where star pickets are suitable for intermediate support, make sure they are driven to a consistent depth and positioned so mesh can be securely fastened. Selected 1650 mm and 1800 mm star pickets are available from Yarra Valley Rural Fencing while stocks last, but the right picket length and spacing should always be determined by the fence design rather than what happens to be on hand.
Get the bottom detail right
Animals do not always challenge a fence in the obvious way. Rabbits, foxes and similar pests will test the lowest point, especially where rain has washed soil away or livestock have worn a track beside the mesh. Small gaps become larger quickly once an animal finds a regular route.
Depending on the species and site, the lower section may need to be buried, turned outward as an apron, pinned to the ground, or protected with a combination of these methods. Burial can work well in stable soil, but it is less reliable where rock prevents consistent depth or where water regularly scours the ground. An outward apron can be effective against digging, provided it is well secured and kept covered or pinned so it cannot lift.
Creek lines, spoon drains and culverts deserve special attention. They are natural travel routes and difficult places to maintain a continuous barrier. The fence needs to accommodate water flow without leaving a permanent opening underneath. This may involve purpose-built mesh arrangements, closely fitted panels or other site-specific details. The best solution depends on how much debris and water moves through the area.
Tension mesh evenly, not brutally
High-quality mesh is only as effective as its installation. Roll it out along the prepared line, allow for the direction of the slope and keep it positioned correctly before applying tension. Pulling too hard can distort the mesh, overload posts and make later repairs difficult. Too little tension leaves a fence that sags, catches debris and gives animals room to push through.
Work from strong end assemblies and tension in controlled stages. On uneven ground, follow the contours as closely as practical and use posts to hold the mesh at the correct level. Do not assume that a straight top line means the bottom is sealed. Check the ground clearance all the way along, particularly over humps and through dips.
Fasten mesh securely to posts and strainers using suitable clips, ties or staples for the materials involved. Fasteners should hold the mesh firmly without damaging the coating or creating sharp protrusions. Where electric offsets are part of the design, they must be correctly positioned and maintained. Electricity can improve deterrence, but it will not compensate for poor construction, sagging mesh or unprotected gaps.
Treat gates as part of the fence, not an afterthought
A well-built exclusion fence can fail at the first gateway. Gates need enough clearance to swing freely without leaving a gap underneath, and latches should be reliable enough that they close every time. On uneven ground, consider how seasonal movement, mud and vehicle traffic will affect the opening.
Use gates sized for the equipment that genuinely needs to pass through. An oversized opening adds cost and creates more opportunity for sagging or poor alignment. Where regular ute, tractor or stock access is needed, strong gate posts and a firm, well-drained approach are worthwhile.
For property owners needing specific rural gates, 12 ft / 3.6 m and 14 ft / 4.2 m farm gates are currently available for direct purchase while stocks last. They are selected stocked items, not a full retail fencing range, so it is sensible to confirm availability before planning around them.
Inspect early and keep on top of repairs
The first few weeks after installation are the best time to find issues. Walk the line after rain, strong wind and the first period of noticeable animal pressure. Look for washed-out soil, lifted mesh, loose ties, leaning posts, fallen branches and fresh tracks at gates or low points.
After that, regular inspections prevent small repairs becoming a long section of replacement fencing. Keep vegetation from loading up the mesh, remove debris where it collects, and fix damage before animals turn it into an established crossing. A fence does not need to look brand new to work well, but it does need to remain continuous, tight and properly secured at ground level.
For difficult ground, long boundaries or fencing where livestock and exclusion needs overlap, professional installation can save costly rework. The practical goal is simple: build the fence for the animals and the land in front of you, then give it the attention needed to keep doing its job.


Comments