top of page
Search
Can Livestock Fences Follow Contours Safely?

Can Livestock Fences Follow Contours Safely?

Nov 5
6 min read

A fence that runs straight across a steep Yarra Valley paddock can look tidy on a plan, then become difficult to build, maintain and use once the posts go in. So, can livestock fences follow contours? Yes, often they can, and following the land can be the sensible choice. But a contour line is not automatically the best fence line. The job is to balance stock control, drainage, access, fence tension and the way the property is actually worked.

Can livestock fences follow contours on sloping land?

A contour fence follows the natural level of a hillside rather than running directly uphill or downhill. On rolling country, this can reduce the sharp rises and falls that make a fence hard to strain, hard to drive beside and more exposed to washouts.

For livestock fencing, contouring is particularly useful where a long boundary or internal paddock division crosses a broad slope. It can make post spacing more consistent and help the fence sit closer to the ground. That matters with sheep, goats, calves or smaller livestock that may test a gap under the bottom wire. It can also produce a more practical line for checking fences on a quad bike, ute or on foot.

The answer still depends on what the fence needs to do. A boundary fence may need to meet an existing corner, gate or surveyed line. A horse fence may need a line that gives safe, usable paddocks. An exclusion fence may need to close off a particular area rather than simply follow the easiest ground. Contours are a tool for planning, not a rule that overrides the rest of the job.

Why contour fencing can work well

The main advantage is that it respects the ground rather than fighting it. A fence that travels straight up and over every rise can have sudden changes in angle. Those changes put extra load on wires, strainers and intermediate posts, particularly after stock pressure, wind or wet weather.

Following a gentler line across the slope can reduce those abrupt transitions. It often means fewer awkward low points where wire lifts off the ground and fewer steep sections where animals lean heavily into the fence. If the route is well chosen, it may also avoid the wettest gullies and the most unstable sections of soil.

There is a management benefit as well. Internal fencing should support how you move stock, rotate paddocks and get machinery around. A contour line can create paddocks that are easier to work across a hill. In some situations, it also helps direct stock towards a gate or laneway instead of leaving the gate at the most inconvenient point on the property.

That said, a fence that is easy to install is not always a fence that is easy to manage. A long, curving contour fence can create oddly shaped paddocks or leave small corners that are difficult to graze, slash or inspect. The best line is usually a sensible compromise between the terrain and everyday use.

Where following contours causes problems

Water is the biggest reason to look beyond the contour line. Hillsides collect and move water in ways that are not always obvious during a dry site visit. A fence line that sits across a drainage path can catch sticks, leaf litter and washed-down debris. Over time, this can place pressure on the lower wires, block natural water movement and create erosion around posts.

Gullies, spoon drains, creek approaches and damp seepage areas need special attention. Sometimes the right answer is to change direction, cross the drainage point at a better location or allow for a purpose-built crossing arrangement. Simply pulling a standard fence across a wet low point is often false economy.

Another issue is the way a contour line behaves around spurs and hollows. A route can look smooth from one side of the hill but involve repeated bends once it is pegged out. Every meaningful change in direction needs appropriate support. Trying to force a tightly strained fence around a corner without proper bracing can pull posts out of line or leave the fence slack where it matters most.

Very steep country is different again. On a severe slope, a perfect contour route may be difficult to reach with equipment and impractical to maintain. There may be loose ground, rock, dense vegetation or limited room to safely work. In those areas, a slightly less tidy but more accessible route can be the better long-term choice.

Start with the purpose of the fence

Before deciding whether the fence should follow contours, be clear about its job. Stock type changes the answer. Cattle, sheep, horses and mixed livestock place different pressure on a fence and need different clearances, heights and visibility.

A cattle fence across rolling ground may tolerate a fairly direct route if the strain points are properly designed. Sheep fencing needs closer attention to ground gaps and low areas. Horse fencing needs to avoid layouts that create blind corners, tight pinch points or situations where a horse can become trapped against a fence. If electric fencing forms part of the system, the line also needs to remain clear enough to operate reliably and be easy to inspect.

Then consider how you use the land. Where do stock enter and leave? Which paddocks need vehicle access? Is there a trough, shelter belt, creek crossing or laneway that affects the route? A fence should make those daily tasks easier, not turn them into a workaround.

Fence tension, corners and changes in grade

Wire fencing works because its tension is controlled from properly built end assemblies and strainer points. On undulating ground, it is rarely wise to treat one long run as though it were flat country. Major changes in direction, sharp crests and significant dips can all call for a break in the run and a suitable strainer or stay arrangement.

This does not mean putting a heavy assembly at every minor change in ground level. It means recognising where the force in the fence changes. A contractor assessing the site will look at the length of each run, soil conditions, wire type, terrain and likely stock pressure before deciding where those points should sit.

Post spacing matters too. On a smooth, moderate contour, spacing may remain fairly regular. On a faster change in grade, closer spacing can help keep wires following the ground and reduce gaps. Posts also need enough embedment and holding strength for the soil. Sandy ground, wet ground, rock and filled areas all behave differently.

A common mistake is to focus only on getting the top wire looking straight. The bottom of the fence is just as important. If the ground drops away between posts, animals find the opening quickly. If the fence is forced hard into uneven ground, it can become difficult to maintain and may trap debris after rain.

Plan gates and access before marking the line

Gates are often where a good fence layout becomes genuinely useful. A gate placed neatly on a contour may look logical, but it can be frustrating if the approach is too side-sloping for a ute, stock trailer or machinery. It may also become boggy in winter if water naturally travels through that spot.

Where possible, choose a gate location with firm approach ground, enough room to turn equipment and a layout that allows stock to flow without bunching into a steep corner. A gate at the bottom of a slope can collect runoff and loose material. One at the top may be exposed and awkward for stock movement. The practical answer depends on the property.

If you are replacing an old fence, do not assume the existing gate is in the best place just because it has always been there. Older layouts often reflect a different grazing system, different machinery or a previous owner’s priorities.

A practical way to assess a contour fence line

Walking the proposed route after rain, or at least looking for water marks and soft ground, tells you far more than viewing it from a distance. Mark the key points first, then join them with a route that makes sense on the ground. The key points usually include boundaries, gateways, corners, drainage crossings and places where terrain changes sharply.

A useful site assessment considers four things together:

  • where livestock will pressure the fence and how they will move through the paddock

  • where surface water travels in heavy rain

  • where strainers, stays and changes in fence direction are needed

  • how the fence will be accessed for construction, checking and repairs

The final route may follow contours for much of its length, then angle across a slope to reach a gate, avoid a wet patch or connect to a stronger corner point. That is normal. Good rural fencing is rarely about drawing one perfect line across a map.

For difficult hillsides, established acreage properties or fencing that has repeatedly failed in the same spot, an on-site inspection is worthwhile. Yarra Valley Rural Fencing can assess the terrain, stock requirements and access before recommending a practical route and fence design. It is better to resolve drainage, gate placement and strainer locations at the planning stage than after the wires are strained.

A well-planned fence should suit the hill, but it should also suit the person who has to open the gate in winter, check the wires after a storm and move stock every week. Start there, and the right contour line usually becomes clear.

 
 
 

Recent Posts

See All

Comments


Mobile 0439 008 228

35 Hosie St, Bayswater North VIC 3153
Visits and pickups by appointment only.

  • Facebook
  • Instagram

©2015 by Yarra Valley Rural Fencing

bottom of page